Unitech MS920 Manuel d'utilisateur télécharger pdf (Page 117)

- 111 -

Always enabled

Inhibit after 1 mn

- Protects the product against unwanted conguration by bar code.

- Conguration with bar codes only possible before end of 1 minute timeout

(cycle repeated until no cong code read within 1 minute).

Inhibit after 1 mn

Transparent conguration mode

- Allows you to use your scanner to set up other products (setup commands

are transmitted to the other product but do not affect your scanner).

- Read unconcatenated conguration codes from the setup sheet to set up

another product in transparent conguration mode (not possible with EasySet

online).

Disable (*)

Enable

1 2 ... 112 113 114 115 116 117 118

User's 1
Table of Contents 3
Overview 7
Scanner Detail 8
Getting Started 8
BATTERY CHARGING 9
Specications 10
Bluetooth Function Setting 11
Chapter 2 11
Buffer Mode 12
From SPP to HID 13
From HID to SPP 13
Android Device 13
Check the memory size 14
Buffer Erasing 15
Power Saving 16
BT Module Power Saving 16
HID Keyborad Character Delay 17
HID Keyborad Case 18
HID Keyborad Block Delay 18
HID Keyborad Languages 19
Enter BT Pairing Code 20
Symbologies 21
Chapter 3 21
Start / Stop 22
Check digit 23
Barcode length 24
Codablock 25
Codablock F 26
Code mark 28
Barcode Length 29
Reading range 34
Reading tolerance 34
Unconventional Code 39 35
Special keys interpretation 35
Code 93/ Code 93i 36
Code 128 / GS1-128 38
GS1 - 128 identier 40
ISBT 128 42
DataMatrix 43
Mirrored labels activation 45
EAN / UPC 46
UPC - E1 47
Add - on digits 49
Check digit transmission 50
UPC number system 51
GS1 DataBar (RSS) 54
User dened 55
Expanded 56
Interleaved 2 of 5 58
Length mode 60
Set length L1, L2 and L3 60
Matrix 2 of 5 61
Matrix stop/start char 62
MicroPDF417 66
MSI Code 67
Plessey Code 72
Unconventional stop 73
Model 1 control 75
Inverse video 75
MicroQR activation 76
Standard 2 of 5 77
Operating Settings 84
Chapter 4 84
Scanning / Triggering 85
Autostand 86
Presentation 86
Presentation threshold 87
Trigger timeout (sec) 87
Trigger activation 88
Software Trigger 88
Compose start character 89
Compose stop character 89
Turn off after good read 90
Aimer mode 90
One pull aim and read 91
Duration 91
Bad read message 92
Ignore stand detect 93
Double scan prevention 93
Data decoding security 94
Center decoding 95
Bar code sequence 96
Beeps / LEDs 97
Good read LED duration 99
Error beep 100
Setup beep and LED 100
Multicode beeps 101
Data Transmission Settings 102
Chapter 5 102
Event notication 103
Preprocessing ISCP barcode 104
Unsuccessful decoding 105
Start of read session 105
End of read session 105
Start-up 105
Trigger pulled 106
Trigger released 106
Structured append 106
Symbology identier 107
Preamble 108
Postamble 108
Inter-Character delay 109
Data editing 110
Activate the scenario 111
Scenario 1 111
Scenario 2 112
Scenario 3 112
Scenario 4 113
Scenario 5 114
Scenario 6 114
Scenario 7 115
Chapter 6 116
Transparent conguration mode 117
Worldwide Support 118
Appendix I 118

Commentaires sur ces manuels

Pas de commentaire

Unitech MS920 Manuel d'utilisateur Page 117

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres Unitech MS920