Unitech MS335 Manuel d'utilisateur

Scanner ConfigurationManager Manualfor PC type computers

6Scanner Configuration ManagerKeyboard Wedge, continuedUse Numeric KeypadThe ASCII code for numeric input from the keypad part of thekeyboard is diffe

7Scanner Configuration ManagerBaud RateBaud Rate (bits per second) refers to the speed of the data throughthe RS232 port. If the data error rate is u

8Scanner Configuration ManagerData DirectionThree options are available for data direction: “Send to Host”,“Send to Host & Terminal”, and “Send t

9Scanner Configuration ManagerTerminatorThe Terminator is a command that follows the input of bar codedata. Four different terminators can be selecte

10Scanner Configuration ManagerAim Function for Long Range EngineThe Aim Function causes a laser scanner to output a “pin-point”aiming aid for a speci

11Scanner Configuration ManagerAiming Time for Long Range EngineThe Aiming Time function specifies the duration of the Aim Function(see previous page)

12Scanner Configuration ManagerMagnetic ReaderThe Magnetic Stripe Reader configuration parameters differ fromthe Scanner Port mainly in that magnetic

13Scanner Configuration ManagerTrack 2The recording density of Track 2 is defined as 75 bits per inch.The character configuration (encoding) is 4 bits

14Scanner Configuration ManagerTrack 3The recording density of Track 3 is defined as 210 bits per inch.The character configuration (encoding) is 4 bit

15Scanner Configuration ManagerTerminatorThe Terminator is a command that follows after the bar code data.Four different terminators can be selected h

Scanner Configuration Manager

16Scanner Configuration ManagerMagnetic Reader, continuedTrack 2 Account Number OnlyIf only track 2 is enabled (see previous page), only the accountnu

17Scanner Configuration ManagerMagnetic Reader, continuedTrack 2 Output SequenceTrack 2 output sequence is arranged in the same manner as theTrack 1 o

18Scanner Configuration ManagerBar Code SymbologiesModify the output characteristics of 16 of the most popular bar codesymbologies in current use. Fo

19Scanner Configuration ManagerBar Code Symbologies, continuedStandard 2 of 5 / Toshiba Code (China Postal Code)Maximum Length defines the maximum len

20Scanner Configuration ManagerBar Code Symbologies, continuedCode 128Enabled toggles the ability for the keyboard/scanner to readCode 128 on or off.

21Scanner Configuration ManagerBar Code Symbologies, continuedCode 93Enabled toggles the ability for the keyboard/scanner to readCode 93 on or off. D

22Scanner Configuration ManagerBar Code Symbologies, continuedUPC-ASend Check Digit toggles whether or not to send a check digit.Default is “Send”.•Se

23Scanner Configuration ManagerBar Code Symbologies, continuedEAN-8Send Check Digit toggles whether or not to send a check digit.Default is “Send”.•Se

24Scanner Configuration ManagerBar Code Symbologies, continuedCode 11Maximum Length defines the maximum length the user willaccept for a valid bar cod

25Scanner Configuration ManagerBar Code Symbologies, continuedLabel Code IV and V•Enabled toggles the ability for the keyboard/scanner to readLabel Co

1.TABLE OF CONTENTSPostamble 11. . . . . . . . . . . . . . . . . . . . .Preamble 11. . . . . . .

26Scanner Configuration ManagerData EditingQualifierThe Qualifier section defines the conditions that must be present forthe bar code to be modified,

27Scanner Configuration ManagerData Editing, continuedDelete deletes existing modifier strings.Move Up / Move Down moves the modifiers up and downin r

28Scanner Configuration ManagerData Editing, continuedThe “Everything Else” FormulaIf a formula is entered into the Data Editing area, then all scanne

29Scanner Configuration ManagerFunction Codes (Code 39)F1 (%VA)F4 (%VD)F7 (%VG)F10 (%VJ)Esc (/FK)TAB (/FI)Back Tab (/FJ)Shift Make (/FP)Shift Break (/

30Scanner Configuration ManagerASCII Chart(Characters in parentheses represent Code 39 bar code printing)HT ($I)NUL (%U)SOH ($A)STX ($B)ETX ($C)EOT ($

31Scanner Configuration ManagerASCII Chart, continued ( (/H)’ (/G)& (/F)%$# (/C)” (/B)! (/A)) (/I)* (/J)+, (/L)-./0123> (%I)= (%H)< (%G);

32Scanner Configuration ManagerASCII Chart, continued IHGFEDCBTSRQPONMLKJUVWXYZ[ (%K)\ (%L)] (%M)^ (%N)_ (%O)b (+B)a (+A) ‘ (%W)(Characters in parenth

33Scanner Configuration ManagerASCII Chart, continuedj (+J)i (+I)h (+H)g (+G)f (+F)e (+E)d (+D)c (+C)u (+U)t (+T)s (+S)r (+R)q (+Q)p (+P)o (+O)n (+N)m

34Scanner Configuration ManagerTROUBLE SHOOTINGMost problems that you might encounter with your scanner can besolved by using the following procedures

35Scanner Configuration ManagerIf the scanner appears to scan (emits light andbeeps), but does not output data, try scanning into aword processor or N

TABLE OF CONTENTS, continuedBAR CODE TEST CHART. . . . . . . . . . . . . . . . . 36Track 3. . . . . . .

36Scanner Configuration ManagerBAR CODE TEST CHART8012 3453EAN-8Unitech 128Code 128A22357000599876BCodabar123456789-0Code 11Code 32AO23399013Code 9312

37Scanner Configuration Manager3 045214 834123EAN-130647669 13716UPC-A0212345799UPC-E(01)054123456789(01)659344EAN 1281234558MSI Code0987654321Interle

1Scanner Configuration ManagerThe above icons, from left to right, represent download settings(from computer to scanner), and upload settings (from sc

2Scanner Configuration ManagerThe above four icons are used in the “Data Editing” feature of SCM.From left to right they are the “Add a Formula” icon,

3Scanner Configuration ManagerThe screen to the leftappears. Click on any ofthe selections under“Current Settings” to viewits “Attributes”.Click the

4Scanner Configuration ManagerBeep ToneSelect a value from “None” to “High” to set the loudness of the tone,or select “Low to High” or “High to Low” t

5Scanner Configuration ManagerKeyboard WedgeYour Unitech keyboard contains a built in data decoder or “wedge”that translates raw bar code input into K